INSUWRAP PVC 1500 FB-UV

Single ply PVC waterproofing membrane with fleece-back lamination for exposed roofing system.

Roofing Solutions, Exposed Roofing

Insuwrap PVC 1500 FB-UV is a calendered extruded high polymer waterproofing membrane with fleeceback, (thickness 1.50 mm) ultraviolet resistant with geo textile, manufactured following highest International standards offering high physical properties and long term durability.

Thickness: 1.50mm

Standards Compliance: ASTM D 4434 - Type 2

Product Features

  • Used for an exposed Roofing.
  • UV - stable.
  • Laminated with embedded back fleece.
  • A loose-laid application does not require any priming.
  • Self-extinguishing material is safe in case of fire.
  • High elongation, and  high physical strength.
  • Extended durability during the lifespan, with high retention properties after aging and exposure to service conditions.
Proudly Made in Saudi

Proudly Made in Saudi

Very Low Emission

Very Low Emission

Environmentally Safe

Environmentally Safe

Easy to Apply

Easy to Apply

Application Instructions

Surface Preparation

Clean the top of metal surface, remove all the loose particles and sharp edges to be ready to receive the roofing system. Using proper types of washers screws, a working flat surface should be mechanically fixed to the metal deck. The working surface can be either 50mm thick extruded thermal insulation or 9mm thick plywood. Apply minimum 150 micron thick polyethylene sheet with 100mm overlap of the joints.

Apply one layer of Insuwrap PVC waterproofing membrane, 1.50mm thick with geotextile protection layer ultra violet resistant (1500 FB-UV). This membrane will be fixed by means of mechanical fixation using aluminum or GI metal strips (30mm wide). These strips will be fixed by mechanical fasteners at 40cm spacing on top of the overlapping joints. Then these joints are welded by hot air welding machine and the overlapping will be 50mm minimum. Special metal screws and washers with spacing 300mm of the overlaps can be used instead of holding metal screws.

Apply Insuwrap PVC 1500 FB-UV (1.50 mm thickness) membrane reinforced with high tenacity polyester mesh, ultra violet resistant. This membrane will be fully adhered by Insurbond-106 or equivalent to parapet wall up to 30cm height and the bottom portion of this membrane will be properly dressed op to the gutter drains. PVC coated metal angles will be fixed on the junctions of horizontal membrane and gutter. A double layer of the membrane will be welded by hot air welding on that angle. Install Aluminum flashing at the top edge of the PVC membranes. The flashing will be fixed with fasteners, then the upper bend is filled with sealant.

Downloads

Explore More Products

INSUWRAP INSURBOND 106

Water base one-component adhesive with very strong adhesion properties on all normally occurring substrates and to be used for bonding Insuwrap PVC waterproofing membranes to concrete, cement plaster & metal sheets; where required

INSUWRAP INSURBOND 106 S

One-component adhesive with very strong adhesion properties on all normally occurring substrates and to be used for bonding Insuwrap PVC waterproofing membranes to concrete, cement plaster & metal sheets; where required.

INSUWRAP INSURBOX CEP145

Plastic end box for protecting PU control tube or re-injection grouting tube in basement and tunnel waterproof system

INSUWRAP INSURBOX REP150

A plastic end box for protecting re-injection grouting tube in basement and tunnel waterproofing system

INSUWRAP INSURDISK R100

Plastic discs for temporary and spot fixation of PVC waterproofing membrane in under- ground waterproofing (100 mm diameter).
Need assistance? Feel free to contact us!

Need assistance? Feel free to contact us!

About

We are professional and reliable provider since we offer customers the most powerful and beautiful themes. Besides, we always catch the latest technology and adapt to follow world’s new trends to deliver the best themes to the market.

Contact info

logo

Saudi Arabia’s Leading PVC Waterproofing Manufacturer.

  • 2nd Industrial Area P.O.Box 17579, Riyadh 11494 Kingdom Of Saudi Arabia
  • [email protected]
  • 966 11 498 0332